English
30 ml delay spray aerosol can with fine-mist actuator held in one hand, mist just beginning to form at the nozzle

30 ml Delay Spray Aerosol Can for Timed-Discharge Personal Care Formats

A delay mechanism is a timing problem before it is anything else. Between the finger landing on the actuator and the first mist leaving the nozzle there is a deliberate interval, and the real question is whether that interval repeats on the hundredth press as closely as on the first. Everything after it, dose and cut-off included, follows from the valve.

  • Place of originChina
  • Diameter range22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
  • PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
  • Port of loadingGuangzhou / Shenzhen / Ningbo / Shanghai
  • MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
  • Payment termsT/T, L/C, PayPal, Western Union — for your selection
  • Trade termEXW / DAP / DDP

Product Description

A delay mechanism is a timing problem before it is anything else. Between the finger landing on the actuator and the first mist leaving the nozzle there is a deliberate interval, and the real question is whether that interval repeats on the hundredth press as closely as on the first. Everything after it, dose and cut-off included, follows from the valve.

Key format data: 30 ml nominal capacity. Typical filling applications are delay spray, personal care spray. Other heights and diameters in the same family can be quoted on request, so the size listed here is a starting point rather than a limit.

This aluminium container is produced in-house from aluminium slug to finished printed can. Body forming, shoulder shaping, internal coating, printing and final inspection all run on the same line, so the wall thickness and pressure performance stay consistent from the first sample to the last pallet of a bulk order.

We supply cans only, or a complete package with valve, actuator and cap selected to match your formulation and filling equipment. Free blank samples are available so your laboratory can confirm pressure, spray rate and compatibility before you commit to tooling or a production run.

Specifications

MaterialAluminium 99.5% (one-piece / monobloc body)
DiameterRecommended based on your requirements
HeightRecommended based on your requirements
Nominal volume / weight30 ml
Neck / valve sizeRecommended based on your requirements
Shoulder shapeRecommended based on your requirements
Recommended contentsDelay spray, personal care spray
Internal coatingFood-grade internal lacquer on request
PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
Surface finishHigh gloss / matte / pearl / metallic lacquer
CapPlastic cap — colour matched to your artwork
PackingCarton + pallet, or as per customer instruction
MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
Lead time15–30 days after sample approval

Final specifications are confirmed against your artwork and filling line before tooling.

Product Features

  • A restrictor or a small delay chamber ahead of the stem holds the charge back for a set interval, so mist begins once the can is positioned rather than at the instant of contact.
  • Repeatability is the difficult part. The interval shortens as propellant pressure falls, so the mechanism is specified against end-of-fill condition, not against a freshly charged can.
  • A metered stem closes after a fixed volume, which separates timing from dose and stops a held-down button from draining the chamber in one long discharge.
  • Temperature pulls the interval both ways, slower from a cold can and quicker from a warm one, and a 30 ml fill spends its life at ambient rather than at fill temperature.
  • The body is short, so the valve sits close to the liquid level; little headspace is left to buffer pressure change and the actuator feel stays firm to the final shot.
  • Fine-mist inserts are matched to the stem so a delayed discharge still atomises properly. A coarse port would keep the same timing and deliver a jet instead.

Application Scenarios

Timed-Dose Formats

Products that must be applied to a specific area before discharge starts suit a delayed valve; the pause covers the movement between press and target.

Pocket Packs

A 30 ml body disappears into a jacket pocket, and the short can is easier to keep upright, which matters when the valve is the timing element.

Valve Trials

Trial runs use the small body to prove a valve setting before a larger can is committed, and the timing behaviour carries across the same valve family.

Private Label

Brands building a timed format around their own fill buy can and valve as one unit, so the interval is fixed at crimping rather than assembled later.

Samples & MOQ

Free Blank Samples

Blank cans are supplied free of charge — you only cover the courier cost. Use them to test pressure, spray rate and formulation compatibility.

MOQ 10,000 pcs

Standard MOQ is 10,000 pieces per size and design. Smaller trial quantities can be discussed for a first production run.

Sampling In 3–7 Days

Printed samples typically take 3–7 days. Mass production follows 15–30 days after you approve the pre-production sample.

Customization Options

DiameterStandard range 22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
HeightCustom height from 90 mm to 300 mm (subject to diameter)
Printing1–9 colours offset or silkscreen, plus lacquer and vacuum coating
ValveOne-inch continuous / metered / bag-on-valve, matched to your formulation
CapStandard or custom moulded cap, any colour
SamplesFree blank samples for compatibility testing; printed samples charged

Frequently Asked Questions

The restrictor and the volume held between stem and nozzle. Both are fixed at assembly; the fill only influences how far the interval drifts as pressure falls.

It does. Lower pressure changes how long the release threshold takes to build, which is why the valve is set against the end-of-fill condition rather than the first shot.

Only by changing the valve, not by changing fill volume. A metered stem releases one chamber per press however long the actuator is held down.

20,000 pcs where the valve or can specification is bespoke, 10,000 pcs for the standard body and print. Blank samples before tooling are free.