English
500 ml black aluminium oxygen canister lying in a vehicle door pocket, rigid overcap fitted, base ring resting flat on the pocket lip.

500 ml Aluminium Oxygen Canister for Vehicle Kits and Standby Storage

A canister that lives in a glovebox or a boot spends most of its life at a vibration and humidity level no shelf unit sees, and then gets used in a hurry. The 500 ml format is the one buyers specify when the unit is stocked rather than carried. Supplied for non-medical supplemental use; market-specific requirements are the buyer's responsibility to confirm.

  • Place of originChina
  • Diameter range22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
  • PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
  • Port of loadingGuangzhou / Shenzhen / Ningbo / Shanghai
  • MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
  • Payment termsT/T, L/C, PayPal, Western Union — for your selection
  • Trade termEXW / DAP / DDP

Product Description

A canister that lives in a glovebox or a boot spends most of its life at a vibration and humidity level no shelf unit sees, and then gets used in a hurry. The 500 ml format is the one buyers specify when the unit is stocked rather than carried. Supplied for non-medical supplemental use; market-specific requirements are the buyer's responsibility to confirm.

Key format data: 500 ml nominal capacity. Typical filling applications are oxygen, compressed air. Other heights and diameters in the same family can be quoted on request, so the size listed here is a starting point rather than a limit.

This aluminium container is produced in-house from aluminium slug to finished printed can. Body forming, shoulder shaping, internal coating, printing and final inspection all run on the same line, so the wall thickness and pressure performance stay consistent from the first sample to the last pallet of a bulk order.

We supply cans only, or a complete package with valve, actuator and cap selected to match your formulation and filling equipment. Free blank samples are available so your laboratory can confirm pressure, spray rate and compatibility before you commit to tooling or a production run.

Specifications

MaterialAluminium 99.5% (one-piece / monobloc body)
DiameterRecommended based on your requirements
HeightRecommended based on your requirements
Nominal volume / weight500 ml
Neck / valve sizeRecommended based on your requirements
Shoulder shapeRecommended based on your requirements
Recommended contentsOxygen, compressed air
Internal coatingFood-grade internal lacquer on request
PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
Surface finishHigh gloss / matte / pearl / metallic lacquer
CapPlastic cap — colour matched to your artwork
PackingCarton + pallet, or as per customer instruction
MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
Lead time15–30 days after sample approval

Final specifications are confirmed against your artwork and filling line before tooling.

Product Features

  • A single drawn shell in 99.5% aluminium leaves the 500 ml wall with no seam to watch, which is what allows the body to stay light for its volume.
  • The crimped 1-inch (25.4 mm) cup and a compressed gasket form the whole seal, a joint that tolerates slow dimensional drift across a long storage period better than a threaded closure.
  • Sampled units from each run go through in-house pressure and burst checks before the pallet is released, and filled stock is never reworked after a failure.
  • A broad base ring and a low centre of gravity keep a full canister upright in a door pocket or a boot tray while the vehicle is moving.
  • A rigid overcap needs a deliberate lift before the actuator can be pressed, which is the practical guard against a knock inside a packed boot.
  • Silver, white and black bodies are standard, and the wall takes 9-colour direct print, so a fleet number or a call-off code goes on the can itself.

Application Scenarios

Glovebox and door pockets

A door pocket holds the unit valve-up if the overcap stays on. Check that the pocket has a lip, since a bare shelf lets a full body roll.

Boot and cargo trays

Cargo trays collect tools and straps. A moulded recess or a strap loop stops the canister being knocked flat by a shifting load on a bend.

Fleet and rental vehicles

Rental and fleet operators want one part number across vehicle classes. A single 500 ml body with printed call-off wording cuts the number of variants held.

Workshop standby stock

Stores hold a few units against the day a job goes wrong. Standing stock wants a dark shelf out of sunlight, caps fitted, nothing stacked on top.

Samples & MOQ

Free Blank Samples

Blank cans are supplied free of charge — you only cover the courier cost. Use them to test pressure, spray rate and formulation compatibility.

MOQ 10,000 pcs

Standard MOQ is 10,000 pieces per size and design. Smaller trial quantities can be discussed for a first production run.

Sampling In 3–7 Days

Printed samples typically take 3–7 days. Mass production follows 15–30 days after you approve the pre-production sample.

Customization Options

DiameterStandard range 22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
HeightCustom height from 90 mm to 300 mm (subject to diameter)
Printing1–9 colours offset or silkscreen, plus lacquer and vacuum coating
ValveOne-inch continuous / metered / bag-on-valve, matched to your formulation
CapStandard or custom moulded cap, any colour
SamplesFree blank samples for compatibility testing; printed samples charged

Frequently Asked Questions

Upright, cap fitted, out of direct sun and clear of anything that can press the actuator. A tray with a lip is better than a flat shelf, where a full body will roll.

Print is applied directly to the aluminium and cured. We do not quote a service temperature for a decorated body, so test a printed sample in the conditions you actually park in.

No bracket is included as standard. The base ring is formed to sit flat, so a strap or a moulded recess in a tray holds the unit without a dedicated fitting.

One size and one design starts at 10,000 pcs. Custom printing or a bespoke specification is quoted from 20,000 pcs, and loading ports are Guangzhou, Shenzhen, Ningbo and Shanghai.