English
300 ml white aluminium oxygen canister held beside a rucksack bottle pocket, moulded overcap in place, printed wall facing the camera.

300 ml Aluminium Oxygen Canister for Trail Training and Daily Commute

Between a keyring unit and a vehicle kit sits the format most buyers reorder: a mid-size body that drops into a bottle pocket and still holds enough for a full session. Wall gauge and valve choice matter more here than capacity, since the same shell has to survive a rucksack, a train and a gym bag in one week. Supplied for non-medical supplemental use; market-specific requirements are the buyer's responsibility to confirm.

  • Place of originChina
  • Diameter range22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
  • PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
  • Port of loadingGuangzhou / Shenzhen / Ningbo / Shanghai
  • MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
  • Payment termsT/T, L/C, PayPal, Western Union — for your selection
  • Trade termEXW / DAP / DDP

Product Description

Between a keyring unit and a vehicle kit sits the format most buyers reorder: a mid-size body that drops into a bottle pocket and still holds enough for a full session. Wall gauge and valve choice matter more here than capacity, since the same shell has to survive a rucksack, a train and a gym bag in one week. Supplied for non-medical supplemental use; market-specific requirements are the buyer's responsibility to confirm.

Key format data: 300 ml nominal capacity. Typical filling applications are oxygen, compressed air. Other heights and diameters in the same family can be quoted on request, so the size listed here is a starting point rather than a limit.

This aluminium container is produced in-house from aluminium slug to finished printed can. Body forming, shoulder shaping, internal coating, printing and final inspection all run on the same line, so the wall thickness and pressure performance stay consistent from the first sample to the last pallet of a bulk order.

We supply cans only, or a complete package with valve, actuator and cap selected to match your formulation and filling equipment. Free blank samples are available so your laboratory can confirm pressure, spray rate and compatibility before you commit to tooling or a production run.

Specifications

MaterialAluminium 99.5% (one-piece / monobloc body)
DiameterRecommended based on your requirements
HeightRecommended based on your requirements
Nominal volume / weight300 ml
Neck / valve sizeRecommended based on your requirements
Shoulder shapeRecommended based on your requirements
Recommended contentsOxygen, compressed air
Internal coatingFood-grade internal lacquer on request
PrintingUp to 9 colours · offset lithography, silkscreen, lacquer, vacuum coating
Surface finishHigh gloss / matte / pearl / metallic lacquer
CapPlastic cap — colour matched to your artwork
PackingCarton + pallet, or as per customer instruction
MOQ10,000 pcs per size and design · 20,000 pcs for custom printing and bespoke specifications
Lead time15–30 days after sample approval

Final specifications are confirmed against your artwork and filling line before tooling.

Product Features

  • Drawn as one piece from 99.5% aluminium, the 300 ml body has no side seam, and that seam is exactly where a bag-carried canister takes repeated point load.
  • The valve cup uses the standard 1-inch (25.4 mm) crimp, so one filling head can run this size and the 100 ml unit without a tooling change.
  • Neck face and cup land are cut on a common axis; a stem that sits off square is the usual reason a discharge sputters instead of holding a steady cone.
  • Shoulder radius is kept generous against the bore, which gives the dome more resistance to a knock than a short, tight shoulder of equal volume would.
  • In-house pressure and burst testing is run batch by batch, and each record is filed against the filling date rather than the dispatch date.
  • A moulded cap with a friction skirt covers the actuator in transit and leaves enough purchase for a gloved hand on a cold morning.

Application Scenarios

Bottle pocket fit

A 300 ml body sits in a side bottle pocket without stretching the mesh. Check pocket depth against the drawing before committing artwork to the lower wall.

Gym and studio bags

Kit bags get loaded and dropped. The rolled base knuckle and straight wall are what stop the shell ovalising when a full body lands on a locker floor.

Commuter rucksacks

A commuter pack presses the canister against a laptop sleeve and a water bottle. The rigid overcap takes that contact so the actuator is not pressed in transit.

Club and coaching stock

Coaches buy one design and reorder through a season. Blank silver stock can run short first, then move to a standing order at 10,000 pcs.

Samples & MOQ

Free Blank Samples

Blank cans are supplied free of charge — you only cover the courier cost. Use them to test pressure, spray rate and formulation compatibility.

MOQ 10,000 pcs

Standard MOQ is 10,000 pieces per size and design. Smaller trial quantities can be discussed for a first production run.

Sampling In 3–7 Days

Printed samples typically take 3–7 days. Mass production follows 15–30 days after you approve the pre-production sample.

Customization Options

DiameterStandard range 22 / 25 / 28 / 35 / 38 / 40 / 45 / 50 / 53 / 59 / 66 mm
HeightCustom height from 90 mm to 300 mm (subject to diameter)
Printing1–9 colours offset or silkscreen, plus lacquer and vacuum coating
ValveOne-inch continuous / metered / bag-on-valve, matched to your formulation
CapStandard or custom moulded cap, any colour
SamplesFree blank samples for compatibility testing; printed samples charged

Frequently Asked Questions

Volume decides how much fill the body carries, but stem bore decides how quickly it leaves. A restricted stem on 300 ml gives a slower, steadier delivery than a wide-open stem on a smaller can.

The catalogue record for the 300 ml canister carries volume only, so we issue the dimensional drawing with the sample instead of quoting a figure here.

The standard cap is a friction-skirt overcap. Tell us how the unit will be carried and the cap is matched to that, since webbing and pocket edges press in different places.

Blank samples leave in 3–7 days. Production follows at 15–30 days after the sample is signed off, with a standard minimum of 10,000 pcs per size and design, or 20,000 pcs where custom printing is involved.