English

Sunscreen Aerosol Actuators: Mist, Continuous Spray And BOV

Sunscreen is one of the hardest things to spray well: the formula is often thick, alcohol-based or loaded with solids, and the user judges it by coverage. The actuator and the valve are where that is decided.

Sunscreen is a difficult product to package as a spray. The formula is frequently thick, alcohol-based, or carrying mineral solids, and none of that is friendly to a small orifice. The user then judges the product by whether coverage is even, a judgement made on the first press.

This page is about the component that press acts on: the actuator, and the valve it has to be specified with. For the can bodies themselves, see our article on cosmetic aerosol cans.

Aerosol actuator for cosmetic sunscreen spray cans
An aerosol actuator of the type specified for cosmetic sunscreen sprays. Illustrative component photograph: the actuator is supplied as part of a matched valve, actuator and cap set.

Three discharge characters, three different component sets

Fine mistMist valve and mist actuator
Facial products applied to a small area
Continuous sprayContinuous valve and actuator
Body products applied while the hand is moving
Bag-on-valveBOV valve, actuator and bag
Formulas that should not contact the propellant, and any-orientation use

These are not three settings on one component set. Each is a different valve and actuator pair, and the pairs are not interchangeable. Choosing the discharge character is therefore the first decision of the project, not a refinement at the end.

Where the formula constrains the component

  • Solids and viscosity. A formula carrying mineral filters or a thick emulsion puts more demand on the valve orifice and the actuator insert, which is why these two are specified for the formula rather than for the can.
  • Alcohol content and compatibility. What the product touches has to survive the claimed shelf life. The internal coating of the body is where that is settled; the nozzle material is the other half of the same question.
  • Orientation in use. A body product is often sprayed at an angle. A bag-on-valve format allows the can to work in any orientation, which is one of the practical reasons it is specified for sun care.
  • Propellant contact. If the formula must stay separate from the propellant, the choice is made at this level, not on the body. See how BOV works.

The bodies these components are matched to

100 mlFacial mist, setting spray
Fine mist actuator
150 mlHydrating mist, body mist
Fine mist or continuous actuator
200 mlSunscreen, continuous spray, after-sun
Continuous spray or BOV
300 mlHair spray, strong-hold styling
Continuous or mist actuator

All four use the same 1-inch (25.4 mm) opening, so the same actuator and cap families are available across the range and the component decision does not have to be taken again if the size changes.

Frequently asked questions

Why is continuous spray usually specified for sunscreen?

Because sunscreen is applied to a large area and the user has to keep the can at a working distance while moving it. A continuous valve releases as long as the actuator is held, which suits that motion. A fine mist valve releases in short bursts and suits a facial product better than a body product.

Should sunscreen use bag-on-valve?

BOV is often specified when the product should not meet the propellant, and it also allows the can to be used in any orientation, which matters for a body product. We make a 200 ml sunscreen body specified for BOV continuous spray. Whether it is worth the extra cost depends on the formulation and the claim you make, so it is a decision to take with the fill volume in front of us. Our BOV article sets out when the format pays for itself.

Can the actuator handle a thick or high-solids formula?

The actuator and the valve are specified together for the formula, not on their own. Tell us the viscosity, the solids content and the propellant, and we will confirm which actuator and valve pair is used and how the discharge is checked before the batch is released.

What sizes do you make for sunscreen and cosmetic sprays?

The sizes relevant here are 100 ml for facial mist and setting spray, 150 ml for hydrating mist and body spray, 200 ml for sunscreen and continuous spray, and 300 ml for hair spray and strong hold styling. All use the same 1-inch (25.4 mm) opening.

Do you supply a cap with the actuator?

Yes. Caps and actuators are available as a set so the actuator is supplied with something that covers it in transit. Printing on the body is done in-house by offset lithography and colour-matched against your approved Pantone reference, so print and component are settled in the same conversation. Free blank samples are available; standard minimum order quantity is 10,000 pieces per size and design.

Next step

Send us the formula characteristics, meaning viscosity, solids and alcohol content, together with the application you are aiming at, and we will confirm which valve and actuator pair fits, with free blank samples to test the discharge. The component is listed under actuator for cosmetic sunscreen spray, and the related sizes under beauty and personal care cans. Or contact us directly.